Thai Web
Upgrade Springfree
Springfree Tgoma
7 FT Sanook Trampoline
Springfree Trampoline With Tgoma
Our Products
Mini Trampoline
SmartplayOnly Trampoline
Springfree Trampoline
Springfree Accessories
Springfree Spareparts
Trampoline Spareparts
Product for Rent
Rectangle Trampoline
Premuim Trampoline
Tgoma New Innovation
Smart Play Only
Customer Reviews
Photo Album
News and Events
Springfree Installation Manual
SmartPlayOnly Installation
FAQ
Interestin​g Aritcles
Link
bulletTgoma Springfree
bulletsanooktrampoline
bulletspringfreetrampolinethailand
bulletspringfree
bulletTrampoline.net
bulletvitaminsdirect.nz
dot
VDO
dot




Quick Tip Installation Guides article
  1.  R54 - Compact Round Trampoline [Download]
  2. R79 - Medium Round Trampoline [Download]
  3. O92 - Large Oval Trampoline [Download]
  4. S113 - Large Square Trampoline [Download]
  5. S155 - Jumbo Square Trampoline [Download]

2. Assembling the Frame

ALL MODELS

Springfree™ Trampoline supplies two flat wrenches to fasten the bolts and nuts. If you have your own sockets / wrenches at home however, you can use one 1/2" (13mm) socket wrench and one 1/2" combination wrench.
Method for ensuring leg Centre Posts are correctly in place and that enclosure nets are not caught between the seat of the centre post and the frame:

  1. Before beginning to join the net and mat rods to the frame ensure centre posts are as best under the frame as possible i.e. the inside edge of the rubberized seat of the post is under the frame. It is important at this point also to ensure the seat of the post is turned in position ready to be accommodated by the curve of the frame.
  2. Once the net and all mat rods are correctly in place ensure no netting is sitting on top of any centre post seat.
  3. After connecting the 1st rod at each 1st rod position to the mat recheck that the net is still not caught between the seat of the centre post and frame and where necessary push each centre post further under the frame (even if only a fraction).
  4. After connecting a further 2 rods at each ‘station’ thus exerting more pressure on the frame and legs recheck the net is not caught and again push each centre post further under the frame as necessary.
  5. After connecting a further 4 rods at each ‘station’ continue as in step 4.
  6. Once all rods are in place and the net is up on mat recheck that centre posts are in correct position.

Note: If at any time any centre post is not properly positioned beneath the frame it may be necessary to hit the post sharply with the base of the hand. Should this not work NEVER use a hammer or similar object. The situation can only be rectified by releasing some of the pressure from the mat rods in the affected area and continuing as in step5.

R54 MODEL - FRAME ASSEMBLY

[Watch Video]
During the installation of your R54 trampoline, the frame initially may not meet together or sit tightly on the centre leg upstands.
Upon completing the installation, the mat rods will tension the frame and seat normally.
 
Although one or more centre leg upstand may not entirely meet the frame, this is normal and will not affect the use, safety or product lifespan whatsoever.


R79 MODEL - SPECIAL TIPS FOR INSTALLATION

[Watch Video]
The Springfree™ Trampoline R79 model has a unique frame socket system. The “frame socket” is where the rods that support the trampoline jumping mat are inserted into the frame.
NB:  It is very important to ensure the rods are correctly and fully inserted into the “frame socket” otherwise the black plastic insert may be damaged.

Before you begin inserting the rods into the frame sockets, ensure all the plastic inserts are installed correctly; Figure 1 shows the insert in the correct position, note both halves of the end of the insert are visible and the wedge shaped clip is positioned against the edge of the slot.  Figure 2 shows the insert in the wrong position, note only half of the insert is visible and the wedge shaped clip is away from the edge of the slot.

O92 MODEL - FRAME ASSEMBLY

[Watch Video]
If after the installation of your O92 trampoline, the mat appears to have a dip or wave at the curved end sections (as in the picture below), the frame sections may be incorrectly installed.
 

tanding at either curved end of your Springfree™ Trampoline, the right hand curved frame section will have 10 mat rod sockets and the left hand frame section will have 11.

This will be the same for both curved frame section ends (see pic below).

3. Attaching the Mat

ALL MODELS

Warning: Treat any loaded rod with caution until you are sure it is properly installed or uninstalled. Keep your face well clear of any loaded rod.
 

When inserting the rods, grab the rod underhand and use the weight of your body, not just your arm strength, to push the rod in. Lift the mat with the other hand as you push the rod under the cleat position and then lower it onto the ball at the top of the rod. Make sure the ball is fully engaged in the cleat.


If you miss the cleat on the first try, we find it's helpful to bring the rod back to its initial position and try again, rather than trying to find the proper position while the rod is flexed.
 

Extra Tip: You will likely find that some of the mat rods in the corners require more applied force in order to get them into the mat edge socket. If you find that the distance between the rods and the mat is too great, have a second person push on the already attached rods on the opposite corner of the trampoline. It is also helpful if they brace the frame on the opposite side to keep it from sliding while you are inserting the rods.

4. Positioning the Enclosure Net and Inserting the Rods

ALL MODELS

The D-Ring on the door of the enclosure net should be facing towards the ground when inserting the rod through the hole into the frame. If the D-Ring is facing up, the net will be inside out.

Ensure that all rods are fully inserted into the bottom of the sockets.
 

5. Raising the Enclosure Net

ALL MODELS

Warning: Never attempt to remove an enclosure rod from its joiner or remove a C-Clip from its slot in the joiner while the enclosure rod is under tension.
When inserting the enclosure rods, first insert the short segment with the white ball into the pocket at the top of the enclosure. Next, insert the long segment into the appropriate socket on the frame ensuring that the plastic C-clip locks it into place.
 




Manuals

Download Manuals article